ASTM A493 PDF

Above values from ASTM A Higher strengths can be produced by heavy cold work – this may be required for certain applications. ASTM A – 16 Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging. This specification covers. See the chemical composition and physical properties of ASTM A Grade annealed Stainless Steel, find alternative materials, and connect with suppliers.

Author: Mogor Nagrel
Country: Georgia
Language: English (Spanish)
Genre: Automotive
Published (Last): 25 June 2016
Pages: 416
PDF File Size: 18.95 Mb
ePub File Size: 15.21 Mb
ISBN: 415-3-56749-317-4
Downloads: 77566
Price: Free* [*Free Regsitration Required]
Uploader: Zubei

An electroplated copper coating is often used. General Requirements for Delivery 4. The producer should be consulted when material is required to tensile strength ranges other than those specied.

This specification covers cold-finished and hot-finished stainless steel wire and wire rods for cold heading or cold forging for applications, such as fasteners, where corrosion resistance is a factor. Copyright ASTM Standard Specication for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging1 This standard is issued under the xed designation A ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

The following coatings may be specied: Packaging and Package Marking 9. The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

  HIPERANDROGENISMO E PELE PDF

ASTM A for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

Resistance to Intergranular Corrosion 8. Link to Active This link will always route to the current Active version of the standard.

The material shall also conform to the requirements as to mechanical properties. Such requirements may include, but are not limited to the following: The values aztm in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

NOTE 1—A typical ordering description is as follows: A superscript epsilon e indicates an editorial change since the last revision or reapproval. The SI equivalents are in parentheses and may be approximate.

ASTM A493 for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

ICS Number Code For smaller sizes, similar mechanical properties apply to ferritic and martensitic grades; however the producer should be consulted regarding somewhat higher tensile properties applicable to austenitic grades. This standard has been approved for use by xstm of the Department of Defense. A number in parentheses indicates the year of last reapproval.

The steel shall conform to the xstm chemical composition requirements. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. This abstract is a brief summary of the referenced standard.

  BS EN 12504-3 PDF

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Soap is generally used. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.

Originally published as A — B Product analysis tolerance over the maximum limit for carbon and nitrogen to be 0. It is informational only and not an official part of the standard; the full text of the standard itself x493 be referred to for its use and application. Material can be manufactured to tensile strength ranges other than those shown in Table 2.

The following lubricants may be specied: Last previous edition A — Current edition approved Jan. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn. Historical Version s – view previous astk of standard. All austenitic grades in the annealed condition or annealed and lightly drafted condition shall be capable of passing the criteria set by this specification.